diff --git a/board/Marvell/dreamplug/dreamplug.c b/board/Marvell/dreamplug/dreamplug.c
index 7ba1402..d15faa1 100644
--- a/board/Marvell/dreamplug/dreamplug.c
+++ b/board/Marvell/dreamplug/dreamplug.c
@@ -1,8 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0+
 /*
- * Copyright (C) 2021  Tony Dinh <mibodhi@gmail.com>
- * (C) Copyright 2011
- * Jason Cooper <u-boot@lakedaemon.net>
+ * Copyright (C) 2021-2022 Tony Dinh <mibodhi@gmail.com>
+ * Copyright (C) 2011 Jason Cooper <u-boot@lakedaemon.net>
  *
  * Based on work by:
  * Marvell Semiconductor <www.marvell.com>
@@ -11,16 +10,19 @@
 
 #include <common.h>
 #include <init.h>
-#include <miiphy.h>
-#include <net.h>
+#include <netdev.h>
 #include <asm/arch/cpu.h>
 #include <asm/arch/soc.h>
 #include <asm/arch/mpp.h>
 #include <asm/global_data.h>
-#include "dreamplug.h"
 
 DECLARE_GLOBAL_DATA_PTR;
 
+#define DREAMPLUG_OE_LOW	(~(0))
+#define DREAMPLUG_OE_HIGH	(~(0))
+#define DREAMPLUG_OE_VAL_LOW	0
+#define DREAMPLUG_OE_VAL_HIGH	(0xf << 16) /* 4 LED Pins high */
+
 int board_early_init_f(void)
 {
 	/*
@@ -90,83 +92,15 @@
 	return 0;
 }
 
+int board_eth_init(struct bd_info *bis)
+{
+	return cpu_eth_init(bis);
+}
+
 int board_init(void)
 {
-	/* adress of boot parameters */
+	/* address of boot parameters */
 	gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
 
 	return 0;
 }
-
-static int fdt_get_phy_addr(const char *path)
-{
-	const void *fdt = gd->fdt_blob;
-	const u32 *reg;
-	const u32 *val;
-	int node, phandle, addr;
-
-	/* Find the node by its full path */
-	node = fdt_path_offset(fdt, path);
-	if (node >= 0) {
-		/* Look up phy-handle */
-		val = fdt_getprop(fdt, node, "phy-handle", NULL);
-		if (val) {
-			phandle = fdt32_to_cpu(*val);
-			if (!phandle)
-				return -1;
-			/* Follow it to its node */
-			node = fdt_node_offset_by_phandle(fdt, phandle);
-			if (node) {
-				/* Look up reg */
-				reg = fdt_getprop(fdt, node, "reg", NULL);
-				if (reg) {
-					addr = fdt32_to_cpu(*reg);
-					return addr;
-				}
-			}
-		}
-	}
-	return -1;
-}
-
-#ifdef CONFIG_RESET_PHY_R
-void mv_phy_88e1116_init(const char *name, const char *path)
-{
-	u16 reg;
-	int phyaddr;
-
-	if (miiphy_set_current_dev(name))
-		return;
-
-	phyaddr = fdt_get_phy_addr(path);
-	if (phyaddr < 0)
-		return;
-
-	/*
-	 * Enable RGMII delay on Tx and Rx for CPU port
-	 * Ref: sec 4.7.2 of chip datasheet
-	 */
-	miiphy_write(name, phyaddr, MV88E1116_PGADR_REG, 2);
-	miiphy_read(name, phyaddr, MV88E1116_MAC_CTRL2_REG, &reg);
-	reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
-	miiphy_write(name, phyaddr, MV88E1116_MAC_CTRL2_REG, reg);
-	miiphy_write(name, phyaddr, MV88E1116_PGADR_REG, 0);
-
-	/* reset the phy */
-	miiphy_reset(name, phyaddr);
-
-	printf("88E1116 Initialized on %s\n", name);
-}
-
-void reset_phy(void)
-{
-	char *eth0_name = "ethernet-controller@72000";
-	char *eth0_path = "/ocp@f1000000/ethernet-controller@72000/ethernet0-port@0";
-	char *eth1_name = "ethernet-controller@76000";
-	char *eth1_path = "/ocp@f1000000/ethernet-controller@76000/ethernet1-port@0";
-
-	/* configure and initialize both PHY's */
-	mv_phy_88e1116_init(eth0_name, eth0_path);
-	mv_phy_88e1116_init(eth1_name, eth1_path);
-}
-#endif /* CONFIG_RESET_PHY_R */